Product Description
USED Texas Star High-Power RF Relay SP2-DC12V (Part # SP-DC12 / AR1021) for DX1200, DX1600, DX2400 & DX3600
These are USED but perfect working order. Handle extreme RF switching currents and restore positive Transmit/Receive (T/R) relay actuation in high-wattage multi-pill linear amplifiers with this genuine Panasonic / Matsushita SP2-DC12V Power Relay (factory cross-reference SP-DC12 / AR1021). Engineered with heavy-duty 15-Amp silver-alloy contacts and high dielectric isolation, this 12V DC 8-pin DPDT relay is built specifically to survive the severe RF power throughput and thermal loads found in flagship Texas Star DX1200 and DX1600 amplifiers, and may also fit DX2400 and DX3600 multi-board decks.
⚠️ MODEL FITMENT & VERIFICATION NOTE
Confirmed OEM factory fitment for Texas Star DX1200 and DX1600 amplifiers. This relay may also work on Texas Star DX2400 and DX3600 models depending on production revision—always verify the existing relay part number (SP-DC12 / SP2-DC12V / AR1021) and 8-pin PCB footprint before ordering or installing.
Product Specifications & Technical Data
- Manufacturer / Brand: Panasonic Industry / Matsushita Electric Works (Factory OEM Service Part)
- Part Numbers / Cross-Reference: SP2-DC12V / SP-DC12 / AR1021
- Nominal Coil Voltage: 12.0 VDC
- Coil Resistance & Power: ~480 Ohms (±10%) / ~25 mA nominal operating current (300 mW coil power)
- Contact Arrangement: DPDT (Double Pole Double Throw / 2 Form C)
- Contact Rating & Material: 15A @ 250V AC / 10A @ 30V DC (300W max switching capacity); Heavy-Duty Silver Alloy Contacts (≤ 30 mΩ initial contact resistance)
- Package & Mounting Style: Heavy-Duty 8-Pin Through-Hole PCB Mount Power Relay
- Compatible Amplifier Models:
- Confirmed Direct Fit: Texas Star DX1200, Texas Star DX1600
- Additional Potential Fitment: Texas Star DX2400, Texas Star DX3600 (verify existing relay stamping prior to installation)
Installation & Bench Notes
- Diagnoses & Solves: Welded or arc-pitted contacts from hot-switching high RF power, severe receive signal loss through high-resistance contacts, intermittent keying on high-output stages, or an open 480-ohm 12V relay coil.
- CRITICAL BENCH DIAGNOSTIC WARNING: Welded T/R relay contacts on high-power 1200W–3600W amplifier decks are frequently caused by hot-switching (keying without proper SSB delay or loose remote keying lines) or transmitting into a high antenna SWR fault. Always inspect antenna matching, coaxial jumpers, and SSB delay timing circuits before returning the amplifier to full-power service.
- BENCH INSTALLATION PROCEDURE:
- Disconnect all primary heavy-gauge DC power cables and coaxial lines from the amplifier chassis and verify internal power supply filter capacitor banks are completely discharged. Use ESD-safe bench practices.
- Locate the SP-DC12 / AR1021 relay on the main RF switching board and note its pin-1 orientation before removal.
- Carefully desolder all 8 heavy terminal pins from the underside of the PCB using a high-wattage, temperature-controlled soldering iron and heavy desoldering braid or a vacuum desoldering station. Avoid excessive dwell time so heavy copper ground planes do not lift.
- Clean the PCB through-holes and surrounding pads thoroughly with high-purity isopropyl alcohol to remove carbonized flux and arc residue.
- Seat the new Panasonic SP2-DC12V relay flush against the circuit board, verify pin alignment, and solder all 8 terminals cleanly using 63/37 eutectic solder to ensure solid mechanical and electrical fillets on both sides of the board.
- Connect a high-power 50-ohm dummy load and wattmeter, apply low exciter drive first to verify crisp T/R switching and low insertion loss, then test at full rated output.