Galaxy Potentiometer mic/rf gain with Push Switch DX95T2

$11.95
In stock
(0) Write a Review
SKU:
RV10203603

Product Description

RV10203603 Dual Concentric 1KA / 1KB Potentiometer with Push Switch (Galaxy DX95T2 OEM)

Restore smooth modulation response, precise receiver front-end attenuation, and multi-function push-switch feature engagement to your high-power mobile transceiver with this genuine OEM-spec Dual Concentric 1KΩ Potentiometer with Integrated Push Switch Assembly. Sourced under Galaxy factory part number RV10203603 (designated as Pot 53 on official parts control charts), this specialized control combines a 1K Audio Taper (1KA) Mic Gain element and a 1K Linear Taper (1KB) RF Gain element on concentric shafts with an integrated push switch, serving as the exact factory service replacement for front-panel controls on Galaxy DX95T2 mobile transceivers.

Product Specifications & Technical Data

  • Galaxy Factory Part Number: RV10203603
  • Parts Chart Designator: Pot 53
  • Component Type: Dual Concentric Rotary Panel-Mount Potentiometer with Integrated Rear Push Switch
  • Resistance Ratings & Tapers:
    • Section 1 (Mic Gain): 1kΩ Audio Logarithmic Taper ("A" Curve / 1KA)
    • Section 2 (RF Gain): 1kΩ Linear Taper ("B" Curve / 1KB)
  • Switch Type: Integrated Rear Push Switch (SPST / DPDT feature actuator)
  • Component Function: Front-Panel Dual Concentric Mic Gain & RF Gain Level Adjustment paired with Integrated Push-Switch Feature Actuation (e.g., Talkback On/Off or Frequency Readout Dimmer)
  • Shaft Geometry: Dual Concentric Independent Shafts (Designed for Stacked Outer/Inner Front Knob Sets with Axial Push Travel)
  • Mounting Configuration: Threaded Metal Bushing with Lock Washer & Hex Nut for Panel Mount; Direct PCB Solder Pins
  • Quality Standard: 100% Factory Original Equipment Manufacturer (OEM) service replacement component
  • Compatible Radio Models:
    • Galaxy DX 95T2 High-Power Mobile SSB Transceiver
    • Select Galaxy, Ranger, and Connex high-power mobile chassis utilizing the RV10203603 (Pot 53) dual 1KA/1KB push-switch potentiometer assembly

Bench Installation & Tech Notes

  • Diagnoses & Solves: Scratchy audio during Mic Gain or RF Gain adjustments, dead spots in receiver sensitivity, erratic modulation levels, unlatching push-switch contacts, or mechanically bound concentric shafts on high-power mobile front panels.
  • BENCH INSTALLATION PROCEDURE:
    • Disconnect DC power from the transceiver chassis and remove top and bottom outer covers to access the front sub-chassis PCB.
    • Loosen set screws or carefully pull off both the inner and outer front-panel concentric control knobs.
    • Unscrew the front bezel retaining hex nut and lock washer from the threaded metal bushing.
    • Desolder the PCB solder pins from the dual potentiometer terminals and push-switch lugs using a temperature-controlled station and desoldering pump, noting wiring/pin layout for both sections (1KA Mic Gain vs 1KB RF Gain vs Switch Lugs).
    • Remove the damaged potentiometer from the sub-chassis frame.
    • Position the new RV10203603 potentiometer into the mounting slot, ensure proper concentric shaft alignment, and secure it firmly using the retaining washer and hex nut.
    • Solder the circuit connections to the PCB pads using 63/37 eutectic solder, ensuring clean solder joints without bridging adjacent pins or switch contacts.
    • Reinstall the inner and outer control knobs, check proper axial clearance for push-switch actuation, power up the transceiver into a high-power dummy load, and test both rotary adjustments and push-switch functions for clean, reliable operation.